>Highlights:
- Kompatibel zu allen PoE fähigen Netzwerkkameras
- HighPower PoE
- Einfache Isntallation: nur mit Siwtch verbinden
- Priorisierung und Energiemanagement entfällt
- Kompaktes Design
> Grundeigenschaften
- Farbe: Schwarz
- Produkttyp: Smart Home Zubehör
> Technische Beschreibung
- High-Power PoE: liefert 15,4 W
- PoE-Standard: IEEE802.3af
> Lieferumfang
- LUPUSEC PoE Injector 1 Kanal, versorgt jedes PoE-Gerät
Allgemeine Informationen
- Hersteller:
- LUPUS-Electronics GmbH
- Hersteller-Webseite:
-
- Marke:
- LUPUS
- Produktbezeichnung:
- 10808 PoE -Injektor
- Produkttyp:
- PoE -Injektor
Technische Informationen
- Schutz:
- Transientenschutz
- Überstrom
- Überspannung
Stromversorgung
- Netzspannung:
- 120 V Wechselstrom
- 230 V Wechselstrom
- Maximale Ausgangsspannung:
- 56 V Gleichstrom
- Mindesteingangsstrom:
- 1,30 A
- Maximale Eingangsstromstärke:
- 2,50 A
- Mindestfrequenz:
- 47 Hz
- Maximale Frequenz:
- 63 Hz
- Maximale Ausgangsleistung:
- 36 W
Schnittstellen / Anschlüsse
- Eingänge:
- 1 x 10/100/1000Base-T
- Ausgänge:
- 1 x PoE
Abmessungen / Gewicht / Farbe
- Formfaktor:
- Serverschrank montierbar
Verschiedenes
- Kompatibilität:
- Cisco VoIP Telefone: Cisco Aironet Access-Point:
- Umweltfreundlich:
- Ja
- Ethernet Schnittstellen Typ:
- Gigabit Ethernet
- Ethernet LAN Datentransferraten:
- 10,100,1000 Mbit/s
- Verkabelungstechnologie:
- 10/100/1000
1 Channel Power over Ethernet injector POE-1HP is a low cost 1-Port High Power midspan injector. It is functionally compliant to the IEEE802.3af standards. Cat6 cables into 10/100/1000 Base T systems, eliminating the need forpower management and prioritization. APPLICATIONS Security Camera with Pan/ Tilt/ Zoom IP Print Servers FEATURES Fully Compliant with IEEE802.3af 10/100/1000 base T compatible Full ProtectionOCP, OVP Full Power of 15.4W per port Cisco AP1250 Full Power Support rack mount possible Cisco: no extern parts required for Legacy devices: VoIP Phones (7910, 7912, 7940, 7960) Access points (350, 1100, 1200) SAFETY Isolation Test Primary to Secondary: 4242VDC for 1min. 10mA, Primary to F.G.: 2121VDC for 1 minute, Output to F.G.: 2121VDC for 1 minute Insulation Resistance Primary to secondary: >10M OHM 500 VDC, Primary to F.G.: >10M OHM 500 VDC OUTPUT DC Output 56V @ 15.4W per port Regulation Functional requirements of IEEE802.3af INPUT AC Input Voltage Range 90 to 264 VAC Leakage Current 3.5 mA max @ 254 VAC 60 Hz AC Input Frequency 47-63 Hz AC Inrush Current 30A(RMS) max. for 115VAC/ 60A(RMS) max. for 230VAC AC Input Current 2.5A for 90VAC / 1.3A for 240VAC GENERAL Effi ciency 75% (typical) at max. load and 120VAC 60Hz Hold-up Time 16mS min. 120VAC and max. load Transient O/P Voltage Protection 60V max. at switch on and off at any AC line Phase Turn-On Delay Time 3 sec max. at max. load, and 120VAC 60Hz, 25Hz Regulation Functional requirements of IEEE802.3af EMC Conducted & radiated Emission EN55022 Class A, FCC Class A with UTP Cabling EN55022 Class B, FCC Class B with FTP Cabling Immunity EN50082-1 ESD EN61000-4-2. Level 3 RS EN61000-4-3. Level 2 EFT EN61000-4-4. Level 2 Surge EN61000-4-5. Level 3 CS EN61000-4-6. Level 2 Voltage Dips EN61000-4-11 Harmonic EN61000-3-2 Class A ENVIRONMENTAL Temperature Operation 0 to +40°C, Non-operation -25 to +65°C Humidity Operation 5 to 90%